JustBeginning
Beginner's guide

So you're getting into woodworking

Woodworking has one of the most rewarding learning curves of any hobby. Within a few weekends you'll make something real that will outlast you. The trick is knowing what to buy first. The right starter kit is smaller than you think, and the wrong purchases are very easy to make.

By Colin B. · Published May 15, 2026 · Last reviewed August 7, 2026
woodworker turning wood on a lathe with shavings flying in a workshop

Photo by Andrew Ruiz on Unsplash

The 60-second version

If you only buy 3 things to start:

  1. Narex Bevel Edge Chisel Set, 4-Piece — The best beginner chisels money can buy: sharp out of the box, properly hardened, made in the Czech Republic.
  2. DEWALT 20V MAX Circular Saw 6-1/2-Inch (DCS391B) — The DeWalt 20V circular saw is the one cordless power tool that unlocks everything else.
  3. Starrett C11H-12-4R Combination Square, 12" — A Starrett combination square is the layout tool you'll use on every project for the rest of your life.
Budget total
$200
Typical total
$450
You can start with hand tools for around $200. A modest power tool setup runs $400–500. Either way, the tools last for decades, not consumables.

We earn commission on qualifying Amazon purchases — see our affiliate disclosure. Price tiers and budget totals shown above are editorial estimates; actual Amazon prices vary.

At a glance

Our top pick in each category

The fastest path through this guide — each best-starter pick by category. Scroll for the budget and upgrade alternatives.

CategoryTop pickPriceWhere to buy
ChiselsNarexNarex Bevel Edge Chisel Set, 4-Piece$$ See on Amazon →
SawsDEWALTDEWALT 20V MAX Circular Saw 6-1/2-Inch (DCS391B)$$$ See on Amazon →
Layout & MeasuringStarrettStarrett C11H-12-4R Combination Square, 12"$$$ See on Amazon →
JoineryTitebondTitebond II Premium Wood Glue, 16 oz$ See on Amazon →
Sanding & FinishingDEWALTDEWALT Orbital Sander Kit, 5-inch (DWE6421K)$$ See on Amazon →
PlanesStanleyStanley No. 4 Smoothing Bench Plane (12-136)$$ See on Amazon →
Before you buy anything

A few things worth knowing first

Decide on hand tools or power tools first. They're different hobbies that happen to make the same things. Hand tools are quieter, cheaper to start, and work in a small apartment. Power tools are faster and better for production work but need space and money. Most woodworkers end up using both, but pick a direction for year one.

Don't buy a table saw yet. Every beginner thinks the table saw is the centerpiece. It isn't. You can make almost everything with a circular saw, a drill, and basic hand tools. A table saw is a year-two purchase, once you know what you're actually building.

Your first projects should be small and structural. A box, a shelf, a simple stool. Not a dining table. The mistakes on small projects cost you an hour; the mistakes on a dining table cost you a week and $300 in lumber.

The gear

What you actually need

a circular arrangement of woodworking tools arranged in a circle

Photo by Immo Wegmann on Unsplash

Chisels

Chisels are the most fundamental hand tool in woodworking. You'll use them on every project, regardless of whether you're a hand-tool or power-tool woodworker. The quality spectrum in chisels is enormous. Cheap hardware-store chisels (think big-box store house brands) come with soft steel that dulls instantly and can't hold an edge. Good chisels from respected makers hold an edge, sharpen easily, and last a lifetime. The Narex chisels are the go-to beginner recommendation in almost every woodworking forum because they hit the sweet spot of genuinely sharp steel at a beginner price.

Best starter
Narex

Bevel Edge Chisel Set, 4-Piece

$49.00 as of Jun 22, 2026

Our rating · In Stock

Made in the Czech Republic from chrome-manganese steel hardened to Rc 59, the Narex chisels arrive nearly sharp and take a keen edge with minimal effort. The four-piece set (1/4", 1/2", 3/4", 1") covers almost every beginner task. Professional woodworkers recommend these as the best chisels under $80, a claim that has held up for a decade.

What we like

  • Chrome-manganese steel holds a razor edge longer than budget chisels
  • Arrives nearly sharp; minimal setup before first use
  • Czech-made quality at under $80, the community standard for years

What to know

  • Needs 20–30 min with a sharpening stone before first use
  • Handles can loosen over time with heavy mallet work
See on Amazon →
Budget pick
IRWIN Marples

Chisel Set, 4-Piece

$

Our rating

The Marples line has been around for generations and the quality is reliable. High-carbon steel, comfortable handles, and widely available. Not as refined as the Narex at the same price, but a solid set if you find them on sale or prefer a more familiar brand.

What we like

  • Widely available at most hardware stores and big-box retailers
  • Proven high-carbon steel that's served woodworkers for generations

What to know

  • Softer steel than Narex, dulls faster under heavy use
  • Less refined fit and finish than pricier options
See on Amazon →
gray tile saw

Photo by Blaz Erzetic on Unsplash

Saws

Every woodworker needs a way to cut wood to length and to shape. Your choice here depends entirely on your tool path. Hand tool woodworkers reach for a quality handsaw first; power tool woodworkers reach for a circular saw. You'll eventually want both, but pick the one that fits your space and budget now.

Saws — what's the difference?

A few common shapes, each making a different trade.

Hand Tools

Quieter, cheaper to start, smaller footprint. Slower to cut, but more skill-building.

Noise
Very low, apartment-friendly
Startup cost
$150–250
Space needed
A workbench + small storage

Best for Apartment dwellers, those who want a meditative craft, furniture makers who value precision over speed

Tradeoff Cutting sheet goods (plywood) by hand is exhausting, not practical for cabinet-scale work

↓ See our pick
Power Tools

Faster, handles larger projects, better for plywood and dimensional lumber.

Noise
Loud; hearing protection required
Startup cost
$300–600
Space needed
Garage or dedicated shop space

Best for Anyone building furniture, home improvement projects, or working with sheet goods

Tradeoff Higher startup cost, needs dust management, loud enough to disturb neighbors

↓ See our pick
Best starter
DEWALT

20V MAX Circular Saw 6-1/2-Inch (DCS391B)

$$$

Our rating

The DCS391B is the power tool that unlocks woodworking. Cordless, 6-1/2-inch blade, enough power for construction lumber and plywood. Pair it with a straight-edge guide and you can make accurate cuts that rival a table saw for most beginner projects. Battery not included. Buy it as part of a DEWALT 20V kit if you don't have the platform yet.

What we like

  • Cordless freedom with enough power for construction lumber and plywood
  • Works with the entire DEWALT 20V battery ecosystem

What to know

  • Battery sold separately; add $50–80 if you don't own 20V tools yet
  • Lighter than a corded saw, can drift on cuts without a guide fence
See on Amazon →
Budget pick
Bahco

244-22-U7/8-HP Hardpoint Handsaw

$

Our rating

The best handsaw under $30. Bahco is a Swedish tool maker with a century-long reputation for quality edges. The 244's hardpoint teeth are permanently hardened: they stay sharp far longer than a standard saw and you can't resharpen them, but that's fine at this price point. For hand-tool beginners or anyone without space for power tools, start here.

What we like

  • Hardpoint teeth stay sharp through hundreds of cuts
  • Under $30, lowest startup cost of any woodworking saw

What to know

  • Can't be resharpened; replace the saw when it finally dulls
  • Slower than a circular saw for sheet goods and repetitive crosscuts
See on Amazon →

Layout & Measuring

"Measure twice, cut once" is a cliché because it's true. Woodworking accuracy starts with layout tools. The combination square is the one tool woodworkers use constantly: it marks 90° and 45° lines, checks squareness of assembled joints, and gauges depth of rabbets and dados. Buy a good one and you'll use it for life. Cheap squares are inaccurate and teach you bad habits.

Best starter
Starrett

C11H-12-4R Combination Square, 12"

$$$

Our rating

Starrett has made precision tools in the US for 150 years and the combination square is their flagship. Ground-steel blade, cast iron head, true to within a fraction of a thousandth. This is the square that professional woodworkers, machinists, and instrument makers rely on. It costs around $80. That's not cheap for a square, but it's cheap for a tool you'll use on every project for decades.

What we like

  • Ground-steel blade accurate to fractions of a thousandth, genuinely precise
  • Cast-iron head stays calibrated for decades of daily use

What to know

  • Around $80, significantly pricier than budget alternatives
  • Heavy and substantial; some find it clunky for quick layout tasks
See on Amazon →
Budget pick
Empire

Level E250 12-Inch True Blue Combination Square

$

Our rating

For around $25 you get a square that's accurate enough for most beginner work. Empire's True Blue line is better than hardware-store house brands and good enough to learn on. When your work demands more precision, upgrade to the Starrett.

What we like

  • Under $25, lets you start accurate layout work without a big investment
  • Accurate enough for most beginner furniture and joinery work

What to know

  • Plastic components wear faster than cast-iron alternatives
  • Less reliable at the extremes; verify with a reference edge before trusting
See on Amazon →
beige wooden plank

Photo by Sarah Worth on Unsplash

Joinery

How you connect pieces of wood together is joinery, and it's the heart of woodworking. You have three paths: mechanical fasteners (screws, nails, fast but ugly), glue joints (clean but slow to set up), or pocket hole joinery (a middle path that's fast, strong, and beginner-friendly). The Kreg Jig is the power tool that beginners don't expect to love but almost universally do: it lets you make strong, hidden screw joints in minutes with almost no skill.

Best starter
Titebond

II Premium Wood Glue, 16 oz

$

Our rating

Wood glue is the foundation of almost every joint in furniture-grade woodworking. Titebond II is the standard: waterproof, sands clean, and has enough open time to get your clamps on before it grabs. The 16 oz bottle lasts most beginners through their first year of projects.

What we like

  • Creates bonds stronger than the surrounding wood fibers
  • Waterproof formula works for both indoor and outdoor projects

What to know

  • 30-minute open time demands quick assembly on complex multi-piece joints
  • Requires clamps; you can't substitute for them on any real joint
See on Amazon →
Upgrade pick
Kreg

K4 Pocket Hole Jig

$$

Our rating

The Kreg jig lets beginners build cabinet-quality frames without mastering traditional joinery. Drill at an angle, drive a special screw, and you have a strong hidden joint in 30 seconds. Genuinely useful in professional shops too. If you're building shelves, cabinets, or face frames, it pays for itself on the first project.

What we like

  • Makes strong hidden joints in 30 seconds without advanced woodworking skills
  • Used in professional shops too; it's not just a beginner shortcut

What to know

  • Pocket holes are weak in tension, wrong for joints that get pulled apart
  • Requires dedicated Kreg screws, an ongoing consumable cost to factor in
See on Amazon →
man using sander on beige wooden surface

Photo by Paul Trienekens on Unsplash

Sanding & Finishing

The quality of your finish depends almost entirely on the quality of your sanding, not the stain or the topcoat. Most beginners sand too little, with too coarse a grit, and wonder why the finish looks terrible. A random-orbit sander makes this dramatically less painful and produces a better result than hand sanding for flat surfaces. End-grain and inside corners still need hand sanding: sandpaper and a block.

Best starter
DEWALT

Orbital Sander Kit, 5-inch (DWE6421K)

$79.08 as of Jun 22, 2026

Our rating · In Stock

The DWE6421K is one of the most recommended beginner sanders in woodworking forums, and for good reason. The 5-inch pad fits standard hook-and-loop discs, the dust bag works, and the 3-amp motor handles hardwoods without bogging down. This is the sander we'd tell a friend to buy without hesitation.

What we like

  • 5-inch hook-and-loop discs are the universal standard, easy to source anywhere
  • Dust bag works well enough for most hobby shop situations

What to know

  • Dust bag misses fine particles; add a shop vac for serious sanding sessions
  • Fixed-speed motor offers less control than variable-speed alternatives
See on Amazon →
Specialty pick
STUHAD

165-Piece Sanding Disc Assortment, 5-Inch

$

Our rating

You need multiple grits to sand properly: typically 80 grit to remove machine marks, 120 to smooth, 180–220 for final prep before finish. This assortment covers the whole range and gives you enough discs to complete a dozen projects before restocking.

What we like

  • Covers all grits from stock removal through final finishing prep
  • Enough discs to complete a dozen projects before restocking

What to know

  • Lesser-known brand; quality consistency can vary between batches
  • You'll burn through coarse-grit discs faster than the assortment ratio implies
See on Amazon →
a close up of a wooden object on a table

Photo by Bailey Alexander on Unsplash

Planes

A hand plane is optional for beginners but transformative once you have it. It lets you flatten a surface, fit a door, thin a board, or create a glassy smooth finish that sandpaper can't match. The No. 4 smoothing plane is the starter plane: it does everything you need in a first plane. The Stanley is inexpensive and works well after a quick tune-up (flattening the sole, sharpening the iron).

Best starter
Stanley

No. 4 Smoothing Bench Plane (12-136)

$$

Our rating

The Stanley No. 4 is the classic beginner plane, the one woodworkers have reached for since the 1860s. The modern version needs some work out of the box (flatten the sole on sandpaper, sharpen the iron), but once tuned it works beautifully. Around $45, it's affordable enough to not stress about while you're learning.

What we like

  • Classic design unchanged for 160 years; every online tuning guide applies directly
  • Under $50, the most affordable entry point into hand plane woodworking

What to know

  • Ships with a dull iron and rough sole; needs 30 min of setup before first use
  • Lighter casting than vintage Stanleys; requires more skill to hold a straight line
See on Amazon →
Upgrade pick
Stanley

Sweetheart No. 4 Premium Bench Plane

$$$

Our rating

The Sweetheart line is Stanley's premium offering: A2 steel iron that holds an edge dramatically longer than the standard model, better machined body, and arrives sharp enough to use. It's around $150 and bridges the gap between the entry-level Stanley and a full Lie-Nielsen or Veritas (which run $300+ and are sold direct from the manufacturer).

What we like

  • A2 steel iron holds an edge 3–4x longer than the standard model
  • Arrives sharp enough to use; minimal setup required out of the box

What to know

  • $150 puts it in the same conversation as quality used vintage planes
  • Easy to confuse with the standard 12-136: confirm you're buying the Sweetheart
See on Amazon →
Going deeper

Your first month of woodworking

Most beginners either buy way too much or stall before making anything. Here's the honest timeline: what you'll actually learn, make, and mess up in the first thirty days.

Read the guide →
Save your money

What you don't need yet

Beginners get pressured to buy a lot of stuff that doesn't help them play better. Here's what we'd skip on day one.

  • A table saw — Every beginner thinks this is the centerpiece of a shop. It isn't. A circular saw with a guide handles everything you'll build in year one. Buy a table saw when you know exactly what you're building and why a circular saw doesn't cut it anymore.
  • A router — Incredibly useful, eventually. But routers have a learning curve, require a router table setup to be really useful, and won't come up for the first 5–10 projects a beginner makes.
  • A miter saw — Great for trim work and crosscuts. Not necessary if you have a circular saw and a speed square for a guide. Add it when trim work, picture frames, or repeated crosscuts become a regular part of your builds.
  • A full set of hand planes — You don't need a jointer plane, a jack plane, and a smoother. Start with one No. 4. The other planes solve specific problems you won't encounter for months.
  • Exotic wood — Build your first five projects from construction-grade pine or poplar. They're cheap, easy to work, and forgiving of beginner mistakes. Learn on cheap wood. Graduate to walnut and cherry when your technique is solid.
First week

Your first seven days

A short, real plan to get from gear-on-doorstep to actually playing.

  1. Choose your tool path: hand tools or power tools. Read the variants section above and commit to one direction for now. · Action
  2. Order the Narex chisels; they're your most-used hand tool regardless of which path you take. · Buy
  3. Order a combination square. You cannot do accurate work without one. · Buy
  4. Pick a first project. A small box, a wall shelf, or a simple step stool. Something you can finish in a weekend. · Action
  5. Watch Paul Sellers build a workbench on YouTube. Even if you won't build one for months, it gives you a clear picture of how hand-tool woodworking flows. · Learn
  6. Buy a bottle of Titebond II. You'll use it on every project. · Buy
FAQ

Common questions

Should I start with hand tools or power tools?

Both paths lead to the same place, but they feel very different to get there. Hand tools are quieter, cheaper to start ($150–250), and work in any space. Power tools are faster and handle larger projects but need a garage or dedicated space and a $400+ startup cost. Most woodworkers end up with both; pick based on your space and patience level.

What's the single most important tool to buy first?

A sharp chisel and a combination square. You'll use both on every project. Everything else can be borrowed, improvised, or deferred. Not these.

Do I need a workbench?

Eventually yes, immediately no. Your first few projects can be built on a solid table with clamps. A sturdy folding workbench (like the Black+Decker Workmate) costs around $80 and gets you through year one. Build a proper bench when you're sure you'll stick with the hobby.

How much should I expect to spend on lumber?

More than you think. Dimensional lumber at a big-box store runs $3–6/linear foot for pine and $8–15 for hardwoods. A small box project might use $20–40 of lumber; a set of shelves, $60–100. Budget for wood separately from your tool budget.

Is woodworking hard to learn?

The basics (cutting straight, gluing joints, sanding, and finishing) are learnable in a weekend. The craft goes deep enough that there's still something to learn after 40 years. The curve is steep early (the first few cuts are humbling) then levels off quickly.

Can I do woodworking in an apartment?

Yes, with hand tools. A handsaw, chisels, a plane, and a mallet make surprisingly little noise and no dust worth worrying about. Power sanding and circular saws are apartment-unfriendly. Several YouTube woodworkers (Paul Sellers, Rex Krueger) build beautiful work in small spaces with hand tools only.

Going further

Where to next

Related hobbies

Browse by category

Authoritative sources

  • Paul Sellers (YouTube) — The best hand-tool woodworking educator on the internet. Methodical, patient, and endlessly instructive. Start with his common woodworking series.
  • Woodworking for Mere Mortals (YouTube) — Steve Ramsey's power-tool focused beginner channel. Excellent project videos with clear technique. Good for beginners who want to build real things fast.
  • Rex Krueger (YouTube) — Hand-tool woodworking on a budget. Rex is the antidote to expensive-tool woodworking culture. Highly recommended for beginners worried about startup cost.
  • Fine Woodworking — The highest-quality woodworking publication. More intermediate/advanced than beginner, but the free articles on technique are excellent and the community forums are active.
  • r/woodworking — Very active subreddit. Good for project inspiration, the wiki has solid beginner resources, and the tool recommendation threads are the most useful on the web.
  • r/handtools — The hand-tool focused subreddit. Smaller community, more specific. If you're going the hand-tool route, the sharpening and plane setup guides here are essential reading.
  • The Hand Tool School — Shannon Rogers's structured online course for hand-tool woodworking. Paid, but genuinely comprehensive: the closest thing to a formal apprenticeship for self-taught woodworkers.
Two people using a band saw in a workshop

Photo by Mazin Omron on Unsplash

As an Amazon Associate, JustBeginning earns from qualifying purchases. We may also earn commission from other affiliate programs linked on this page. Editorial recommendations are independent; we don't choose products based on commission rates.

Product prices and availability are accurate as of the date and time indicated and are subject to change. Any price and availability information shown on Amazon at the time of purchase will apply.