By Colin B., published November 8, 2026, last reviewed November 8, 2026By Colin B., updated Nov 8, 2026We earn a commission if you buy through our links. How this works
A wooden longbow is one of the oldest tools people have made, and you can build a working one from a hardware-store board and a handful of hand tools. The magic is in tillering: slowly removing wood until both limbs bend evenly. Here's how to pick a board, the rasps and scrapers that do the work, how to check draw weight and how to make your first bowstring.
00
The short version
Starter budget
$58 to $96
How hard
Some practice
Day one
Pick a straight-grained red oak or hickory board about 6 feet long, with grain running the full length of the face.
A straight-grained red oak or hickory board from a lumber store or big-box store is cheap and forgiving. Look for grain lines that run the full length of the face without running off the edges. That single check decides whether the bow survives.
Tillering is the craft.
Most of the work is removing small amounts of wood and checking the bend, over and over, until both limbs curve evenly. Rushing it, or pulling past your target draw, is how most first bows break.
Safety first on every draw.
Wear safety glasses while tillering and on first shots, never dry-fire a bow, and inspect the back for splinters or cracks before each session. A breaking bow can throw splinters at your face.
02
Rasps and spokeshaves
Shaping a bow means taking a board from flat stock down to tapered limbs. A coarse rasp removes wood fast while you rough out the shape; a spokeshave takes long, controlled shavings along a limb. You don't need power tools: a good rasp and patience will get a board bow to rough shape in an afternoon or two.
Best starter$20.98as of Nov 8, 2026★★★★★ our ratingIn Stock
Shinto
9" Shinto Saw Rasp
A rasp made of crossed saw blades that cuts quickly without clogging, so you can rough out limbs fast and still control what you remove. A favorite with bowyers for exactly this job. About $21. 3,300+ reviews at 4.8 stars.
Four tools in one: flat and half-round faces, each with a coarse rasp and a finer file. A cheap, versatile tool for shaping limbs, handles and string nocks. About $14. 132 reviews at 4.5 stars.
A flat spokeshave for taking long, even shavings down the length of a limb. Faster and smoother than a rasp once the bow is roughed out, and a joy when it's sharp. About $37. 672 reviews at 4.1 stars.
Once a bow bends, you switch from rasping to scraping. A card scraper takes off whisper-thin shavings, so you can stiffen-check, scrape a few strokes from the stiff spot and check again without overshooting. Curved scrapers fit the belly of a limb and the handle area. Learning to sharpen a scraper with a burnisher pays off quickly.
Best starter$14.20as of Nov 8, 2026★★★★★ our ratingIn Stock
Generic
Blue Curved Cabinet Scraper Cards
A set of flat and curved card scrapers for fine tillering and smoothing. Cheap, effective and the tool you'll use most in the final stages of a bow. About $14. 2,000+ reviews at 4.7 stars.
Cabinet Scraper Burnisher with 6 Piece Multi-Shaped Scraper Set
Six scrapers in different shapes plus a burnisher to roll a fresh cutting edge when they dull. The burnisher is what keeps scrapers working well through a whole bow. About $20. 108 reviews at 4.5 stars.
Draw weight is how hard the bow pulls at full draw, usually measured at 28 inches. Hang the bow on a tillering stick or tree, hook a digital scale to the string and pull to the mark. Checking weight as you go stops you overshooting your target, and a scale with a measuring tape is handy for marking draw length.
Best starter$8.99as of Nov 8, 2026★★★★★ our ratingIn Stock
Dr.meter
110 lb Digital Luggage Scale with Tape
A digital hanging scale that reads up to 110 pounds, far more than a beginner's bow, with a built-in tape measure. Hook it to the string and pull to read draw weight at a given length. About $9. 27,500+ reviews at 4.6 stars.
Another well-reviewed digital hanging scale with a tape measure, a good alternative if the Dr.meter is out of stock. About $10. 5,600+ reviews at 4.6 stars.
You can buy a bowstring, but making your own is part of the craft. Dacron is the traditional choice for wooden bows because it stretches slightly, which is easier on the limbs than modern low-stretch materials. Flemish twist strings need only string material, wax and a little practice. Avoid Fast Flight-style materials on a first wooden bow.
Best starter$15.38as of Nov 8, 2026★★★★★ our ratingIn Stock
BCY
B55 Bowstring Material
A polyester bowstring material made for traditional and wooden bows, with enough stretch to be kind to limbs. A spool makes many strings. About $15. 197 reviews at 4.6 stars.
Bowstring wax for twisting strands into a Flemish string and protecting it from fraying and moisture. A tube lasts a long time. About $5. 4,100+ reviews at 4.8 stars.
Bow making is learned by doing, but a good book saves a lot of broken bows. The Traditional Bowyer's Bible series is the standard reference, written by experienced bowyers. Volume 1 covers wood selection, design, tillering and strings: everything you need for a first bow. Later volumes go deeper into specific designs and history.
Best starter$31.76as of Nov 8, 2026★★★★★ our ratingIn Stock
Lyons Press
The Traditional Bowyer's Bible, Volume 1
The book most wooden bow makers learned from, covering wood choice, bow design, tillering, finishes and strings. Edited by Jim Hamm. About $32. 234 reviews at 4.7 stars.
The second volume of the series, with more designs, techniques and bowyer know-how for your second and third bows. About $35. 282 reviews at 4.8 stars.
A board bow is the classic first build: one straight-grained board, a few hand tools and a lot of patience. Here's how to go from lumber rack to first arrow over four weekends, with the checks that keep your bow from breaking.
Most first bows that break do so for one of two reasons: a board with bad grain, or tillering that went too far too fast. Get those two right and a board bow is very achievable for a beginner.
Weekend 1: The board and the layout
At the lumber store, sort through the 1x2 or 1x3 red oak or hickory boards and find one where the grain lines on the wide face run end to end, without running out the sides. Ignore color and knots on the edges; grain is what matters. About 6 feet long suits most adult archers.
Mark the center, a handle of about 4 inches, and the limb outline: full width near the handle, tapering to about half an inch at the tips. The back of the bow, the side facing away from you, stays untouched. All shaping happens on the belly and sides.
Rasp the limbs to your outline, then start thinning the belly evenly toward the tips. Keep checking: brace one tip on the floor, hold the handle and press gently on the other end. You’re looking for both limbs to flex a little and evenly. Stiff spots get a few rasp strokes.
When both limbs bend several inches with moderate pressure, cut shallow string nocks near the tips with a file.
Weekend 3: Tillering
Tie a long string, longer than the bow, and put the bow on a tillering stick: a 2x2 with notches every inch. Pull a few inches, step back and look at the curve. Scrape a few strokes where a limb is stiff, then exercise the bow 20 or 30 times before checking again.
Go slowly: a couple of inches deeper each round, checking draw weight with the scale as you approach your target. When you’re bending to about 20 inches evenly, fit a proper string at a low brace height and continue to your full draw. Never pull past your target draw length.
Make a Flemish twist string from B55 string material and wax it, or use a purchased string while you learn. Sand the bow smooth, seal it with an oil or wipe-on finish, and wrap a handle.
Shoot your first arrows at a safe range with a proper backstop, wearing safety glasses. Check the back for lifting splinters after every few shots during the first sessions. A bow that has survived its first hundred shots will usually last a long time.
What not to worry about yet
Don’t worry about staves, backings, recurved tips or heavy draw weights. Build one honest, evenly tillered board bow. Everything else in bow making builds on that.
A four-in-hand rasp, scraper cards, a digital scale, B55 string material and wax come to about $58. A Shinto rasp and The Traditional Bowyer's Bible bring it to about $96. Add $15 to $30 for a straight-grained board from a lumber store.
11
Common questions
What wood should I use for my first bow?
A straight-grained red oak or hickory board from a lumber store. The grain should run the full length of the face without running out the edges. Red oak is cheap and easy to find; hickory is tougher and more forgiving.
What is tillering?
Tillering is shaping the limbs until they bend evenly and the bow reaches its target draw weight. You remove a little wood from stiff areas, check the bend on a tillering stick, and repeat, slowly increasing how far you pull.
How long does it take to make a bow?
A first board bow usually takes a few weekends: an afternoon or two to rough out the shape, then several sessions of careful tillering. Rushing the tillering is the most common reason first bows break.
What draw weight should I aim for?
For a first bow, something like 30 to 40 pounds at your draw length. It's easier to tiller safely, more comfortable to shoot and less likely to break than a heavy bow.
Is it dangerous to make a bow?
The main risk is a bow breaking at full draw. Wear safety glasses, never pull past your target draw, never dry-fire, and inspect the back for damage. Shoot only at a safe range with a proper backstop.