Getting into pen turning

A woodturner shaping a spinning blank with a gouge

Photo by William Warby on Unsplash

Pen turning is the quickest route into woodturning: a small lathe, a block of wood or acrylic, and in an hour you're holding a pen you made. Pens make great gifts and teach every core lathe skill. Here's which mini lathe to buy, the mandrel and bushings that hold the blank, which pen kits to start with and how to get a glassy finish.

00

The short version

Starter budget
$364 to $415
How hard
Some practice
Day one
Order a mini lathe, a mandrel kit, slimline kits, wood blanks, carbide tools and CA glue.

Buy these three first:

01

Before you buy anything

Start with slimline kits.

They use one 7mm drill bit, thin blanks and simple hardware, so they're the cheapest and most forgiving pens to learn on. Once you can turn a slimline cleanly, every other kit is a variation.

Wood or acrylic?

Wood blanks are cheaper, easier to turn and forgiving of a dull tool. Acrylic blanks give bright colors and a glassy shine but chip if you're heavy-handed and need careful sanding. Learn on wood.

You need a way to drill straight holes.

Blanks have to be drilled down the center for the brass tube. A drill press is ideal; a vise and a steady hand drill can work for slimlines. Factor that in if you don't have a drill press already.

02

Mini lathes

A mini lathe with variable speed is the right size for pens and small projects. Look for a #2 Morse taper in the headstock and tailstock, which pen mandrels need, and variable speed so you can turn slower while roughing and faster while finishing. More power and a longer bed matter for bowls and spindles, not pens.

3421 3.2-Amp 8" by 12" Variable Speed Mini Benchtop Wood Lathe
Best starter $238.48 as of Nov 8, 2026 ★★★★★ our rating In Stock
WEN

3421 3.2-Amp 8" by 12" Variable Speed Mini Benchtop Wood Lathe

A compact benchtop lathe with variable speed, an 8-inch swing and 12 inches between centers. Plenty of capacity for pens, bottle stoppers and small bowls, at a price that makes sense for a new hobby. About $238. 1,400+ reviews at 4.4 stars.

We like

  • Variable speed
  • Compact enough for any bench
  • Huge owner community

Know this

  • Small motor for big bowls
70-105 10" x 18" 1/2 hp Mini Lathe
Upgrade pick $399.99as of Nov 8, 2026 ★★★★
RIKON

70-105 10" x 18" 1/2 hp Mini Lathe

A heavier mini lathe with a 10-inch swing, 18 inches between centers and a 1/2 hp motor. A good choice if pens might lead to bowls and larger spindle work. About $400. 206 reviews at 4.5 stars.

We like

  • Heavier and more stable
  • Room to grow into bowls

Know this

  • Speed changes by moving a belt
  • Nearly twice the price
03

Mandrels and bushings

A pen mandrel is a steel rod that fits the lathe's headstock and holds the drilled blanks while you turn them. Bushings sit on either side of each blank and show you exactly how thin to turn so the pen parts fit. A mandrel saver supports the end of the mandrel at the tailstock so it doesn't bend and spoil your concentricity.

PKMS2SET Pen Mandrel Saver Package, #2 Morse Taper
Best starter $29.95 as of Nov 8, 2026 ★★★★★ our rating In Stock
PSI Woodworking

PKMS2SET Pen Mandrel Saver Package, #2 Morse Taper

Everything to mount your first pen: a #2 Morse taper mandrel, a mandrel saver tailstock center, a 7mm drill bit and five 7mm bushings. About $30. 610 reviews at 4.7 stars.

We like

  • Drill bit and bushings included
  • Mandrel saver prevents bending
  • Fits #2 Morse taper lathes

Know this

  • Bushings suit 7mm kits only
PM-002/MT2 Pen Mandrel Saver with TRIM-001 Barrel Trimming System and Tube Insertion Tool
Upgrade pick $59.85as of Nov 8, 2026 ★★★★
PM

002/MT2 Pen Mandrel Saver with TRIM-001 Barrel Trimming System and Tube Insertion Tool

A mandrel kit with a 7mm drill bit and live mandrel saver, plus a universal barrel trimming system that squares blank ends to the tube and a tool for pressing tubes in straight. Squared ends are the secret to pens without gaps. About $60. 69 reviews at 4.3 stars.

We like

  • Barrel trimmer included
  • Tube insertion tool included

Know this

  • Bushings sold separately
04

Pen kits

A pen kit is all the hardware: brass tubes, the tip, the twist mechanism, the clip and the cap. You supply the blank. Slimline kits are the classic first pen because they use thin blanks, one 7mm drill bit and simple assembly. Bolt action, cigar and fountain pen kits come next and need their own bushings and drill sizes.

A turned pen with a wooden and resin barrel on paper

Photo by Megs Harrison on Unsplash

10-Pack 7mm Slimline Pen Kits, 5 Finishes
Best starter $28.99 as of Nov 8, 2026 ★★★★★ our rating In Stock
BRW

10-Pack 7mm Slimline Pen Kits, 5 Finishes

Ten slimline twist pen kits in five plating finishes, enough to practice, make mistakes and still have gifts left over. Uses the 7mm drill bit and bushings from a standard mandrel kit. About $29. 228 reviews at 4.4 stars.

We like

  • Ten kits for about $3 each
  • Five finishes to try
  • Works with 7mm bushings

Know this

  • Budget plating can wear
PKCPBAPAK Bolt Action 30 Cal Ballpoint Pen Kit Starter Set
Specialty pick $39.95as of Nov 8, 2026 ★★★★
PSI Woodworking

PKCPBAPAK Bolt Action 30 Cal Ballpoint Pen Kit Starter Set

Three bolt action pen kits that look like a rifle bolt, plus the matching bushing set. A hugely popular gift pen once you've mastered slimlines. Blanks and the drill bit are not included. About $40. 401 reviews at 4.7 stars.

We like

  • Bushings included
  • Popular, giftable design

Know this

  • Needs its own drill bit size
05

Pen blanks

Pen blanks are small square sticks, usually about 3/4 inch square and 5 inches long. Wood is the easiest start: it cuts cleanly with carbide tools and forgives a few catches. Acrylic and acetate blanks give vivid color and depth but chip if you push too hard, so take light cuts and keep tools sharp.

Exotic Wood Pen Blanks 12-Pack
Best starter $17.49 as of Nov 8, 2026 ★★★★★ our rating In Stock
Generic

Exotic Wood Pen Blanks 12-Pack

Twelve wood blanks in a mix of species, including bloodwood, so you can see how different woods turn and finish. Enough for several slimline pens. About $17. 326 reviews at 4.4 stars.

We like

  • Variety of woods to try
  • Cheap enough to practice on

Know this

  • Quality varies blank to blank
Multi-Colored Variety Acrylic Acetate Pen Blanks (10-Pack)
Upgrade pick $24.95as of Nov 8, 2026 ★★★★
Generic

Multi-Colored Variety Acrylic Acetate Pen Blanks (10-Pack)

Ten colorful acrylic acetate blanks for when you're ready to try plastics. They polish to a deep shine without a CA finish. About $25. 43 reviews at 4.7 stars.

We like

  • Bright, striking colors
  • Polishes to a shine

Know this

  • Less forgiving than wood
06

Turning tools

Carbide tools are the easiest way to start turning. Instead of sharpening a traditional gouge, you rotate or replace a small carbide insert when it dulls. A square cutter roughs a blank round, a round cutter shapes and a pointed or diamond cutter adds detail. Traditional skew chisels give a cleaner finish but take practice and a sharpening setup.

Carbide Tipped Wood Turning Tools Set (Rougher, Finisher, Detailer)
Best starter $49.98 as of Nov 8, 2026 ★★★★★ our rating In Stock
Generic

Carbide Tipped Wood Turning Tools Set (Rougher, Finisher, Detailer)

A set of carbide-tipped turning tools with rougher, finisher and detail cutters, among others. No sharpening needed: rotate the insert when it dulls. A complete starting kit for pens and small projects. About $50. 682 reviews at 4.6 stars.

We like

  • No sharpening needed
  • Covers roughing to detail
  • Very well reviewed

Know this

  • Carbide leaves more sanding than a skew
Woodturning Carbide Lathe Tools, Set of 3 (Rougher, Detailer, Finisher)
Budget pick $34.79as of Nov 8, 2026 ★★★★
Generic

Woodturning Carbide Lathe Tools, Set of 3 (Rougher, Detailer, Finisher)

Three carbide tools, rougher, detailer and finisher, which is all a pen really needs. A cheaper way to start. About $35. 26 reviews at 4.4 stars.

We like

  • The three tools pens need
  • Lower cost

Know this

  • Few reviews
Wood Lathe Tools Set with Carbide Lathe Tools and Bowl Sander
Upgrade pick $77.89as of Nov 8, 2026 ★★★★
RUITOOL

Wood Lathe Tools Set with Carbide Lathe Tools and Bowl Sander

A larger carbide set with a bowl sander included, for turners who expect to move from pens into bowls and bigger spindles. About $78. 89 reviews at 4.6 stars.

We like

  • Room to grow into bowls
  • Bowl sander included

Know this

  • More tools than pens need
07

Glue and finish

CA glue does two jobs in pen turning. Medium CA glues the brass tubes into the drilled blanks. Thin CA, built up in several layers and polished, gives wood pens the hard, glossy finish you see on store-bought pens. Micro-Mesh pads take sanding from scratch-free to mirror-smooth, especially on acrylics.

Medium Super Glue Pro Kit (2 oz)
Best starter $14.79 as of Nov 8, 2026 ★★★★★ our rating In Stock
STARBOND

Medium Super Glue Pro Kit (2 oz)

A medium-viscosity CA glue with precision tips, the right thickness for gluing pen tubes into blanks. It gives you a few seconds to slide the tube in straight. About $15. 10,300+ reviews at 4.7 stars.

We like

  • Right viscosity for tubes
  • Precision tips included

Know this

  • Sets fast, so work quickly
Super Fast Thin CA Glue Pro Kit
Specialty pick $14.79as of Nov 8, 2026 ★★★★
STARBOND

Super Fast Thin CA Glue Pro Kit

Thin CA for the classic pen finish: wipe on a few coats with a paper towel while the lathe spins slowly, then sand and polish. About $15. 15,000+ reviews at 4.6 stars.

We like

  • Builds a hard, glossy finish
  • Same brand as the tube glue

Know this

  • Takes practice to apply evenly
Micro-Mesh Soft Touch Sanding Pads
Specialty pick $20.60as of Nov 8, 2026 ★★★★
Micro-Mesh

Soft Touch Sanding Pads

Cushioned sanding pads in very fine grits that take a CA or acrylic finish from hazy to mirror-bright. Rinse and reuse for many pens. About $21. 2,600+ reviews at 4.7 stars.

We like

  • Mirror finish on CA and acrylic
  • Washable and reusable

Know this

  • Pricier than regular sandpaper
08

Your first ten pens

Pen turning is best learned by making a lot of pens. Here's how to get through your first ten slimlines: safe setup, drilling and gluing, turning to the bushings, a glossy finish and assembly, with what to change on each one.

Hands guiding a turning tool against wood spinning on a lathe

Photo by William Warby on Unsplash

Every pen turner’s first pen has a flaw: a gap, a bump, a cloudy finish. That’s fine. The skills come from repetition, and slimline kits are cheap enough that ten pens is a sensible first goal.

Before pen one: Set up safely

Bolt the lathe to a solid bench at elbow height. Wear safety glasses and a dust mask, tie back hair and roll up sleeves. Keep the tool rest close to the work, about an eighth of an inch away, and always spin the blank by hand before switching on.

Pens 1 to 3: Drilling, gluing and squaring

Cut a blank into two pieces a little longer than the kit’s tubes. Mark which ends meet in the middle so the grain lines up. Clamp each piece and drill straight down the center with the 7mm bit, clearing chips often so the bit doesn’t overheat.

Scuff the brass tubes with sandpaper, coat them with medium CA and push them in with a twist. Once the glue cures, square the ends flush with the tubes using a barrel trimmer or disc sander. This single step prevents most gaps in finished pens.

A turned wooden pen with brass fittings and its cap
Photo by Hope House Press - Leather Diary Studio on Unsplash

Pens 4 to 6: Turning to the bushings

Slide the bushings and blanks onto the mandrel in the order the kit shows, snug the mandrel saver against the end and start at a moderate speed. Rough the blank round with the square carbide cutter using light, sweeping passes.

Then shape. Turn down until the blank is just proud of the bushings, then take the last few passes very gently until it’s flush. Try a gentle curve or a slight bead; slimlines look best with a slim waist toward the center.

Pens 7 to 8: Sanding and finishing

Sand through the grits, from about 180 up to 600, with the lathe at low speed. Stop and sand along the length between grits to remove circular scratches.

For a glossy finish, apply a few coats of thin CA with a folded paper towel while the lathe spins slowly. Let it cure, then level any ridges with fine sanding or Micro-Mesh pads and polish. Practice on spare blanks until it’s even.

A turned pen with a figured wood barrel on a dark desk
Photo by Sahej Brar on Unsplash

Pens 9 to 10: Assembly and gifts

Press the parts together in a vise with wood blocks or soft jaws, following the kit diagram exactly, especially the depth of the twist mechanism. Write with it, then make two more as gifts. Giving pens away is the best motivation to keep improving.

What not to worry about yet

Don’t worry about fountain pens, exotic resin blanks, traditional gouges or a bigger lathe. Make ten slimlines and you’ll know exactly what to try next.

Ready to choose your gear? See our pen turning gear guide.

09

What you don't need yet

Beginners get pressured to buy a lot of stuff that doesn't help them. Here's what we'd skip on day one.

  • A full-size lathe A mini lathe handles pens perfectly. Upgrade when you're sure you want bowls and big spindles.
  • A pen press Slimline kits press together fine in a bench vise with soft jaws or wood blocks.
  • Traditional gouges and a sharpening system Carbide tools need no sharpening. Add a skew and a grinder later if you want cleaner cuts.
  • Fountain pen and premium kits They cost far more per pen. Make ten slimlines first, then step up.
10

Your first seven days

A short, real plan to get from gear-on-doorstep to actually doing it.

  1. Order a mini lathe, a mandrel kit, slimline kits, wood blanks, carbide tools and CA glue.
  2. Bolt the lathe to a solid bench, and wear safety glasses and a dust mask every time you turn.
  3. Cut a blank to the tube lengths, drill it straight with the 7mm bit and glue in the tubes with medium CA.
  4. Square the blank ends to the tubes, then mount them on the mandrel between bushings.
  5. Turn the blank down to the bushings with light cuts, sand through the grits and apply a finish.
  6. Press the pen together following the kit instructions and admire your first pen.
11

What it costs

Budget start
$364
Typical
$415

A WEN mini lathe, a mandrel kit with drill bit and bushings, ten slimline kits, wood blanks, a budget carbide tool set and medium CA glue come to about $364. Our picks, with a better tool set, thin CA for finishing and Micro-Mesh pads, are about $415.

12

Common questions

How much does it cost to start pen turning?

Around $360 to $420 for a mini lathe, mandrel kit, carbide tools, pen kits, blanks and glue. The lathe is most of that. After setup, a slimline pen costs only a few dollars in hardware and wood.

Do I need a drill press?

It's the easiest way to drill straight holes, which matter for a pen that looks right. Slimlines can be drilled with a hand drill and a vise if you're careful, but a drill press saves many ruined blanks.

What's the best first pen kit?

A 7mm slimline. It uses one drill bit, a thin blank and simple hardware, and most mandrel kits come with the right bushings. Once you can turn slimlines cleanly, move up to bolt action or cigar kits.

How do I get a glossy finish on a wood pen?

Sand to about 600 grit, then apply several thin coats of thin CA glue with a paper towel while the lathe spins slowly. Let it cure, level it with fine sanding or Micro-Mesh, and polish to a shine.

Why is there a gap between the pen parts?

Usually the blank ends weren't squared to the tubes before turning. A barrel trimmer or disc sander squares them so the parts meet cleanly. Turning past the bushings can also leave a step.

Is pen turning safe?

With basic care, yes. Wear safety glasses and a dust mask, keep sleeves and hair away from the lathe, use light cuts and keep the tool rest close to the work. Ventilate when using CA glue.

Browse by category
Authoritative sources